Get Dante Level 2 Part B Skills Test Answers

Dante Via's native sample rate is 48 kHz.

Dante Via's native sample rate is 48 kHz.

Dante Via's native sample rate is 48 kHz.

Green indicates that Dante Controller is currently connected to the primary Dante network. Red indicates a problem with the connection. S: The current status of the Secondary Dante network.

Green indicates that Dante Controller is currently connected to the primary Dante network. Red indicates a problem with the connection. S: The current status of the Secondary Dante network.

Green indicates that Dante Controller is currently connected to the primary Dante network. Red indicates a problem with the connection. S: The current status of the Secondary Dante network.

Can a Dante network with 5 switch hops support latency of 1 ms or less? Yes. Minimum recommended latency will be 0,5ms.

Can a Dante network with 5 switch hops support latency of 1 ms or less? Yes. Minimum recommended latency will be 0,5ms.

Can a Dante network with 5 switch hops support latency of 1 ms or less? Yes. Minimum recommended latency will be 0,5ms.

Dante Domain Manager supports redundancy only within a subnet. Redundant audio is not supported between devices in different subnets. DDM will filter subscriptions across subnets to disable redundancy on these subscriptions.

Dante Domain Manager supports redundancy only within a subnet. Redundant audio is not supported between devices in different subnets. DDM will filter subscriptions across subnets to disable redundancy on these subscriptions.

Dante Domain Manager supports redundancy only within a subnet. Redundant audio is not supported between devices in different subnets. DDM will filter subscriptions across subnets to disable redundancy on these subscriptions.

Can the Secondary (redundant) port on a Dante device be connected to the Primary network to increase channel count? No. This will cause the network to fail.

Can the Secondary (redundant) port on a Dante device be connected to the Primary network to increase channel count? No. This will cause the network to fail.

Typically, the 10ms latency should not impact any audio networks you might set up using Dante Via. However, if low latency is your thing, Dante PCIe cards are available, which can deliver extremely low latency (0.15ms).

Can the Secondary (redundant) port on a Dante device be connected to the Primary network to increase channel count? No. This will cause the network to fail.

Typically, the 10ms latency should not impact any audio networks you might set up using Dante Via. However, if low latency is your thing, Dante PCIe cards are available, which can deliver extremely low latency (0.15ms).

While Gigabit switches are recommended, 100Mbps switches may be used in limited scenarios. For channel counts of 32 or more, Gigabit switches are essential.

Typically, the 10ms latency should not impact any audio networks you might set up using Dante Via. However, if low latency is your thing, Dante PCIe cards are available, which can deliver extremely low latency (0.15ms).

While Gigabit switches are recommended, 100Mbps switches may be used in limited scenarios. For channel counts of 32 or more, Gigabit switches are essential.

Audinate has developed a rich suite of diagnostic tools within Dante Controller, providing visibility into the network health status through features such as device latency monitoring, active clock health monitoring, packet error reporting, and bandwidth usage statistics.

While Gigabit switches are recommended, 100Mbps switches may be used in limited scenarios. For channel counts of 32 or more, Gigabit switches are essential.

Audinate has developed a rich suite of diagnostic tools within Dante Controller, providing visibility into the network health status through features such as device latency monitoring, active clock health monitoring, packet error reporting, and bandwidth usage statistics.

Audinate has developed a rich suite of diagnostic tools within Dante Controller, providing visibility into the network health status through features such as device latency monitoring, active clock health monitoring, packet error reporting, and bandwidth usage statistics.

IGMP Snooping is required when: Multicast Dante or AES67 flows are in use. Dante traffic is mixed with other Multicast traffic, such as Multicast video systems. Critical control systems are on the same network as Dante devices, such as Crestron/AMX/Extron control devices.

IGMP Snooping is required when: Multicast Dante or AES67 flows are in use. Dante traffic is mixed with other Multicast traffic, such as Multicast video systems. Critical control systems are on the same network as Dante devices, such as Crestron/AMX/Extron control devices.

IGMP Snooping is required when: Multicast Dante or AES67 flows are in use. Dante traffic is mixed with other Multicast traffic, such as Multicast video systems. Critical control systems are on the same network as Dante devices, such as Crestron/AMX/Extron control devices.

Dante Controller can apply information in a Dante preset to a device of a different model. What is the "golden rule" about Dante redundant networks? A. Do not link the primary and secondary networks - they must remain in separate broadcast domains.

Dante Controller can apply information in a Dante preset to a device of a different model. What is the "golden rule" about Dante redundant networks? A. Do not link the primary and secondary networks - they must remain in separate broadcast domains.

Dante Controller can apply information in a Dante preset to a device of a different model. What is the "golden rule" about Dante redundant networks? A. Do not link the primary and secondary networks - they must remain in separate broadcast domains.

When multiple devices have their Preferred Leader checkbox ticked, the leader will be elected automatically from within that group. If 'Follower Only' is shown instead of a checkbox, it indicates that the device is not capable of acting as a leader clock.

When multiple devices have their Preferred Leader checkbox ticked, the leader will be elected automatically from within that group. If 'Follower Only' is shown instead of a checkbox, it indicates that the device is not capable of acting as a leader clock.

When multiple devices have their Preferred Leader checkbox ticked, the leader will be elected automatically from within that group. If 'Follower Only' is shown instead of a checkbox, it indicates that the device is not capable of acting as a leader clock.

Dante Controller can apply information in a Dante preset to a device of a different model. What is the "golden rule" about Dante redundant networks? A. Do not link the primary and secondary networks - they must remain in separate broadcast domains.

Dante Controller can apply information in a Dante preset to a device of a different model. What is the "golden rule" about Dante redundant networks? A. Do not link the primary and secondary networks - they must remain in separate broadcast domains.

Dante Controller can apply information in a Dante preset to a device of a different model. What is the "golden rule" about Dante redundant networks? A. Do not link the primary and secondary networks - they must remain in separate broadcast domains.