Get Oftec Cd10 Form No Download Needed

The Oftec Cd10 form, also known as the Installation Completion Report, is essential for documenting compliance with installation requirements for oil-fired appliances. This guide provides a clear, step-by-step approach to filling out the form online, ensuring accuracy and adherence to necessary regulations.

Follow the steps to fill out the Oftec Cd10 form accurately online.

1. Click the ‘Get Form’ button to obtain the Oftec Cd10 Form and open it in the editor.
2. Begin by recording the full postal address where the installation works were carried out, including the postcode, and ensure you provide a contact name and telephone number of the responsible person for the property.
3. Enter your company OFTEC registration number, which consists of a four-digit number followed by the letter 'C' (e.g., C1234).
4. Provide your full business name and address for identification and compliance purposes.
5. Record your name as the technician who completed the work or is self-certifying the installation.
6. Enter your OFTEC registration number, which is a five-digit number followed by your OFTEC qualifications (e.g., N/01643/101/102).
7. If a risk assessment (e.g., TI/133D) has been completed, tick the designated box to indicate compliance.
8. Sections 7 to 16 must only be completed by an OFTEC registered technician holding an OFT 600 qualification.
9. For section 17, record the type of appliance installed (e.g., wall-mounted, floor-standing, external).
10. In section 18, provide the manufacturer’s name of the installed appliance.
11. Enter the serial number of the installed appliance, located on the appliance itself.
12. Specify the name of the burner manufacturer in section 20.
13. Tick the appropriate box for the boiler type (regular, combination, condensing, cooker, or room heater).
14. Record the installed appliance model in section 22.
15. Provide the SEDBUK rating or the manufacturer’s stated efficiency of the installed appliance as indicated in the appliance manual.
16. Tick the type of burner installed (Pressure jet, vaporising sleeve, or vaporising pot).
17. Record the model of the burner, which can typically be found on the burner itself.
18. Indicate the type of flue installed (room sealed balanced flue, low level discharge, or conventional open flue).
19. Confirm that the installed flue terminal location complies with the required standards by ticking the appropriate box.
20. Document whether a stainless steel flue liner has been installed.
21. Provide the internal diameter of the flue in millimeters.
22. Record the location of the conventional flue/hearth notice plate, if applicable.
23. Indicate the number of 45º bends in the flue system that has been installed.
24. Document the locations and types of the conventional flue installed.
25. Record the number of access doors fitted in the flue system.
26. Confirm the flueing arrangements are suitable for the fuel type by ticking the relevant box.
27. Provide the combustion air supply measurement in mm² for open flued appliances.
28. Document the ventilation air supply measurement in mm² where applicable.
29. If an extract fan is fitted, tick to confirm compliance with OFTEC guidance.
30. Record compliance with electrical works by providing associated certificates.
31. Tick to confirm that independent time and temperature controls have been fitted.
32. Specify what controls have been installed and the number of heating and domestic hot water zones provided.
33. Confirm that the appliance and system setups have been configured to prevent short cycling.
34. Tick to confirm that all existing systems have been flushed and cleaned.
35. Document that the newly completed system has been flushed and cleaned.
36. Confirm that the correct dosage of a suitable inhibitor has been added to the system.
37. Tick to confirm the installation of a suitable cold water treatment system, if a combination boiler has been fitted.
38. Record the differential temperature between the appliance's primary system flow and return in degrees Celsius according to the manufacturer’s instructions.
39. Provide the sealed system pressure in bars.
40. Finally, review the completed form for any errors and ensure all required fields are accurately filled out. Once verified, you can save your changes, download, print, or share the form as needed.

Ensure your compliance by completing the Oftec Cd10 form online today.